Product Details:
Minimum Order Quantity 1 Piece
Connectivity Type Wireless or Wi-Fi
The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to Serial connector or to the microcontroller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manger of the USB to Serial Adapter. Then you can open Putty or any other terminal software and open an connection to that COM port at 9600 baud rate, which is the default baud rate of this modem.
Once a serial connection is open through the computer or your microcontroller you can start sending the AT commands. When you send AT commands for example: 'ATr' you should receive back a reply from the SIM800A modem saying 'OK' or other response depending on the command send.
Important Note:
The SIM800A requires huge power, so use a 12V DC 2 to 3 Amps adapter, any wrong adapter might cause damage also to the modem.
On the board there are Tx(D) and Rx(D) pins, near the 5V and GND pins, don't ever connect anything to them or send any command to them, they are not the TTL pins for serial communication, they are for upgrading the firmware, and if you connect them to the microcontroller or computer, the firmware will get damaged and the module will stop working.
Please read carefully the marking on the SIM card tray on how to open or close, those are made of brittle plastics and will break if you put too much pressure on them, so be very gentle and careful while removing or inserting SIM Cards.
Don't tight the antenna too much, the screw threads might get damaged by excessive or over tightening of antenna.
Please don't touch the connections or components and always put the modem on a non conductive base.
Product Details:
Minimum Order Quantity 1 Piece
Connectivity Type Wireless or Wi-Fi
The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to Serial connector or to the microcontroller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manger of the USB to Serial Adapter. Then you can open Putty or any other terminal software and open an connection to that COM port at 9600 baud rate, which is the default baud rate of this modem.
Once a serial connection is open through the computer or your microcontroller you can start sending the AT commands. When you send AT commands for example: 'ATr' you should receive back a reply from the SIM800A modem saying 'OK' or other response depending on the command send.
Important Note:
The SIM800A requires huge power, so use a 12V DC 2 to 3 Amps adapter, any wrong adapter might cause damage also to the modem.
On the board there are Tx(D) and Rx(D) pins, near the 5V and GND pins, don't ever connect anything to them or send any command to them, they are not the TTL pins for serial communication, they are for upgrading the firmware, and if you connect them to the microcontroller or computer, the firmware will get damaged and the module will stop working.
Please read carefully the marking on the SIM card tray on how to open or close, those are made of brittle plastics and will break if you put too much pressure on them, so be very gentle and careful while removing or inserting SIM Cards.
Don't tight the antenna too much, the screw threads might get damaged by excessive or over tightening of antenna.
Please don't touch the connections or components and always put the modem on a non conductive base.
Subscribe to get Email Updates!
Thanks for subscribe.
Your response has been recorded.
Tenet Technetronics focuses on “Simplifying Technology for Life” and has been striving to deliver the same from the day of its inception since 2007. Founded by young set of graduates with guidance from ardent professionals and academicians the company focuses on delivering high quality products to its customers at the right cost considering the support and lifelong engagement with customers. “We don’t believe in a sell and forget model “and concentrate and building relationships with customers that accelerates, enhances as well as provides excellence in their next exciting project.